AISI 501 Enquiry | Print this page
- Category
- Type
- Steel grade
- Standard
- Country
- USE
- Grades
- Special Alloy
- » 501
EN X12CrNiMoV12-3
EN X12M5
EN X15CrMo5-1
EN X18CrMoNbVNi1-1
EN X22CrMoV12-1
1.0605
Alloy 52
Alloy 713C
Alloy 713LC
1.4088 - AISI
- USA
- A 194/A 194M (2014) Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both
Chemical composition % of the ladle analysis of grade 501
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Mo(％) |
| 0.15 | 0.50 | 0.30-0.60 | 0.030 | 0.50 | 4.00-6.00 | 0.45-0.65 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 672 (≥) | 384 (≥) | 41 | 13 | 14 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 123 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 332 (≥) | 222 (≥) | 44 | 41 | 24 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 121 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 471 | 211 | 647 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| S20501 | Stainless steel and heat resistant steel |
||
| A 314 S50100 | Stainless Steel Billets and Bars for Forging |
||
| S50100 | Chromium Heat Resisting Steel |
||
| A 1018 HSLAS Grade 65 [450] Class 1 A | Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength Steel |
||
| A 501 Grade A | Hot-Formed Welded and Seamless Carbon Steel Structural Tubing |
||
| A 1018 HSLAS Grade 65 [450] Class 1 B | Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength Steel |
||
| A 501 Grade B | Hot-Formed Welded and Seamless Carbon Steel Structural Tubing |
||
| X2CrNiMoCuWN25-7-4 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
| 1.4501 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
| 2HR501 | Specification for nickel-chromium-cobalt-titanium- aluminium heat-resisting alloy cold drawn wire for springs and springs (Nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
||
| X2CrNiMoCuWN25-7-4 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
| 1.4501 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
| T31501 | Oil-Hardening Tool Steel |
||
| AISI 501 | A 194/A 194M (2014) Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
||
| AISI501 | AISI501 |
||
| ASTM501 | ASTM501 |
||
| AISI501A | AISI501A |
||
| AISI501B | AISI501B |