CNS CNS 405 Enquiry | Print this page
- Category
- Type
- Steel grade
- Standard
- Country
- USE
- Grades
- Special Alloy
- » CNS 405
CNS 317J2
CNS 317J3L
CNS 317J4L
CNS 317J5L
CNS 321
CNS 347
CNS XM15J1
CNS 329J1
CNS 329J3L
CNS 329J4L - CNS
- China
- China Taiwan Stainless steel
Chemical composition % of the ladle analysis of grade CNS 405
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Ni(％) | Al(%) |
| Max 0.08 | Max 1.00 | Max 1.00 | 0.04 | 0.03 | 11.5-15.5 | Max 0.60 | 0.10-0.30 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 118 (≥) | 577 (≥) | 33 | 32 | 44 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 311 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 942 (≥) | 235 (≥) | 31 | 32 | 44 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 131 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 363 | 111 | 312 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| HNV5 | Steel for intake valves |
||
| S63005 | Steel for intake valves |
||
| Z1CNS17-15 | Iron and steel. Austenitic and austenic-ferritic stainless steels plates for boilers and pressure vessels |
||
| Z11CNS17-07Az | Stainless steels for general purposes. Plates, wide strips and strips |
||
| Z15CNS25-20 | Iron and steel. Austenitic and austenic-ferritic stainless steels plates for boilers and pressure vessels |
||
| Z17CNS20-12 | Iron and steel. Austenitic and austenic-ferritic stainless steels plates for boilers and pressure vessels |
||
| Z80CNS20-02 | Valve steels and alloys for internal combustion engines |
||
| A 240 S40500 | Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
||
| A 268 S40500 | Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service |
||
| A 276 S40500 | Stainless Steel Bars and Shapes |
||
| A 473 S40500 | Stainless Steel Forgings |
||
| A 580 S40500 | Stainless Steel Wire |
||
| S40500 | Ferritic Chromium Stainless Steel |
||
| SA-240 S40500 | Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
||
| SA-268 S40500 | Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service |
||
| X17CrNi16-2 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
||
| 1.4057 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
||
| SUS 405 | Stainless steel bars |
||
| SUS 405 | Hot-rolled stainless steel plates, sheet and strip |
||
| SUS 405 | Cold-rolled stainless steel plate, sheet and strip |