Stainless Steel Round Bar | 17-4ph Stainless Steel | Custom Pump Shaft | Specialty Steel Supply

Current Location:Home » steel database » Steel standards » A135 / A135M - 09

steel database category

Tel: 13880247006

E-mail:sales@steel0.com

A135 / A135M - 09

A135 / A135M - 09 Standard Specification for Electric-Resistance-Welded steel Pipe

Abstract

 

This specification covers two grades of electric-resistance-welded steel pipe intended for conveying gas, vapor, water or other liquid. The steel shall be made by either or both basic-oxygen or electric-furnace processes. Steel may be cast in ingots or may be strand cast. The pipe shall be manufactured from flat rolled steel in individual lengths or continuous length by electric-resistance or electric-induction welding without the addition of extraneous material. The weld seam of electric-resistance welded pipe to Grade B pipe shall be heat treated after welding or processed in such a manner that no untempered martensite remains. Tensile and chemical requirements of the steel are provided. Specimens of the steel pipes are subject to flattening test and hydrostatic test. A nondestructive electric test, either electromagnetic (eddy current) or ultrasonic test, may be preferred as an alternate to the hydrostatic test.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the Standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope
 

 

1.1 This specification covers two grades of electric-resistance-welded steel pipe in NPS 2 to NPS 30 [DN 50 to DN 750] inclusive, with nominal (average) wall thickness up to 0.500 in. [12.70 mm], inclusive, and in nominal sizes NPS ¾ to NPS 5 [DN 20 to DN 125] inclusive with nominal (average) wall thickness 0.083 in. [2.11 mm] to 0.134 in. [3.40 mm], depending on size. Pipe having other dimensions (Note 1) may be furnished provided such pipe complies with all other requirements of this specification. The pipe is intended for conveying gas, vapor, water or other liquid; only Grade A is adapted for flanging and bending (Note 2). The suitability of pipe for various purposes is somewhat dependent upon its dimensions, properties, and conditions of service, so that the purpose for which the pipe is intended should be stated in the order. The pipe may be furnished either nonexpanded or cold expanded at the option of the manufacturer. When pipe is cold expanded, the amount of expansion shall not exceed 1.5 % of the outside diameter pipe size.

Note 1—A comprehensive listing of Standardized pipe dimensions is contained in ASME B36.10M.

 

Note 2—This provision is not intended to prohibit the cold bending of Grade B pipe.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the Standard.


2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the Standard.

ASME Standard

B36.10M Welded and Seamless Wrought steel Pipe,
 

Federal Standards

Fed.STDNo.183 Continuous Identification Marking of Iron and steel Products
 

ASTM Standards

A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
E6 Terminology Relating to Methods of Mechanical Testing
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E213 Practice for Ultrasonic Testing of Metal Pipe and Tubing
E273 Practice for Ultrasonic Examination of the Weld Zone of Welded Pipe and Tubing
E309 Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation
E570 Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products
E1806 Practice for Sampling Steel and Iron for Determination of Chemical Composition
 

Military Standards

MIL-STD-129 Marking for Shipment and Storage

 


Index Terms

 

eddy current testing; electric resistance welded pipe; hydrostatic testing; plain end pipe; Schedule 10 pipe; threaded pipe; Electric-resistance-welded (ERW) steel pipe--specifications; Flattening test; Gas pressure systems/applications--specifications; Hydrostatic testing; Liquid environments; Nondestructive evaluation (NDE)--metallic materials; Plain end steel pipe--specifications; Threaded pipe; Vapor transmission; ICS Number Code 23.040.10 (Iron and steel pipes)


 

 


DOI: 10.1520/A0135_A0135M-09




[Back to Top]
1 Page